Number of views:
ZY-1006 Plastic Low Temperature Brittleness Testing Machine
Number of views:
Product serial number
1. Features and uses:
The ZY-1006 rubber-plastic low-temperature brittleness testing machine is to measure the temperature at which the sample is damaged by impact under specified conditions, which is the brittle temperature. It can be used for comparative evaluation of the performance of plastics and other elastic materials under low-temperature conditions. It can measure the brittleness temperature and low temperature performance of different rubber materials or different formulations of vulcanized rubber. Therefore, it is indispensable in the quality inspection of scientific research materials and products, and the control of the production process. This instrument is designed according to the GB/T 5470-2008 standard. It is equipped with a B-type fixture and impact head that can test multiple samples at the same time. This test fixture can hold 5 samples for simultaneous testing.
2. Technical parameters
1. Test temperature and time: -70 degrees (normally more than 1 hour), the cooling time is short, no water cooling is needed, and it is more environmentally friendly.
2. Cooling speed:
0℃ ~ -30℃ 1.2℃/min
-30℃ ~ -40℃ 1℃/min
-40℃ ~ -70℃ 0.7℃/min
3. Impact speed: 2m/s±0.2m/s
4. After the constant temperature, the temperature fluctuation is less than ±0.5℃, and the temperature control is more accurate.
5. The distance from the midpoint of the impactor to the lower end of the holder: 8±0.5mm
6. Dimensions: 900×505×950mm (length×height×width)
7. Effective space of studio: 160×140×100mm (length×height×width)
8. Power: 2000W
Three, structure principle
1 Lifting gripper The lifting gripper is composed of a cylinder with a gripper and a cylinder block.
The distance from the impacted part of the sample to the lower end of the holder is 8.0±0.5mm.
2 Impact device The impact device is composed of an impactor and an impact cylinder.
The weight of the impactor is 200±20g, and its working stroke is 40±1mm. When the impact cylinder is in the reset state, the distance from the end of the impactor to the sample is 25±1mm.
4 Freezing medium: industrial ethanol
5 This measuring instrument uses a compressor for direct cooling. It does not require cooling circulating water.
Four, use method
1 Turn on the power, the temperature controller and timer display lights are on.
2 Inject the freezing medium (usually industrial ethanol) into the cold well. The injection amount should ensure that the holder sample can be immersed below 25mm of the medium liquid level.
3 Clamp the sample vertically on the holder. The clamp should not be too tight or too loose to prevent the specimen from deforming or falling off.
4 After reaching the test temperature, press the start button, and the testing machine will work automatically (press the holder to start freezing the sample, and at the same time start the timing control switch or press the stopwatch to time, the sample freezing time is specified as 3min. The sample freezing period , The temperature fluctuation of the freezing medium shall not exceed ±1℃)
5 Take off the sample and check each sample to determine whether it is damaged. The cracks, cracks, or small holes that appear during the test, or separate into two pieces so that more fragments are defined as damage, when the sample is not broken At the time, bend the specimen 90° in the bending direction formed during the impact, and then inspect the specimen for cracks at the bend.
6 After the sample is impacted (each sample can only be impacted once), if damage occurs, the temperature should be increased by 10℃ to do a new set of tests, and a new sample should be used at each temperature until the sample is not damaged. If there is no damage to the sample, then the temperature is reduced to the highest temperature of damage that has been observed. Control the temperature increase or decrease at a temperature interval of 2°C until the temperature at which a set of samples is not damaged is measured, and this temperature is recorded as the brittle temperature.
5. Sample standard
1 Specification requirements: length 31.75±6.35mm, width 6.35±0.51mm, thickness 1.91±0.13mm
2 Requirements: The surface of the sample should be smooth, free of foreign impurities and damage. The finished product should be cut into corresponding size after grinding.
Six, matters needing attention
The cylinder pressure has been adjusted before leaving the factory and cannot be changed arbitrarily.
We could not find any corresponding parameters, please add them to the properties table
ZY-2000E Rubber Rotorless Vulcanizer
The ZY-2000E computerized rotorless vulcanizer adopts a computer-controlled imported temperature controller for accurate temperature control. The computer can process data in a timely manner and can perform statistics, analysis, storage and comparison, etc., humanized design, easy operation, accurate data, and optimized formula for rubber Provide accurate data. The buttons of the mouse on the computer of this vulcanizer have the same function as the buttons on the host panel, which is convenient for users to operate. The computer software interface is quite good and it is extremely convenient to use. Users can accurately measure the scorch time, positive vulcanization time, and vulcanization index. , Maximum and minimum torque, etc., is the ideal equipment for rubber industry to control the quality of rubber materials, rapid inspection and rubber extrusion research.
Sulfur change meter
1. Introduction: The ZY-2000E rubber vulcanization analyzer adopts a computer-controlled imported temperature controller for temperature control. The computer can process data in a timely manner and can perform statistics, analysis, storage and comparison, etc., humanized design, easy operation, accurate data, and provide accurate rubber formula data. The buttons of the mouse on the computer of this vulcanizer have the same function as the buttons on the host panel, which is convenient for users to operate. The computer software interface is quite good and it is extremely convenient to use. Users can accurately measure the scorch time, positive vulcanization time, and vulcanization index. , Large and small torques, etc. It is an ideal equipment for rubber industry to control the quality of rubber materials, rapid inspection and rubber extrusion research. ZY-2000E Rubber Vulcanometer is a new generation of mechatronics product launched by our factory. It is mainly composed of host, sensor, computer, data collector of lower computer, printer and electric chain. Executive standard: ASTMD5289－95 ISO6502:1991 HG/T3709-2003 Provide vulcanization curve, temperature curve diagram. Single curve test, continuous test of any curve and comparison test of any curve are possible on the same interface, the data is stored in the database, and all curve data can be printed in real time or in history. 2. Technical parameters: Executive standard: GB/T16584, ISO-6502 Cavity structure: fully enclosed Temperature control range: normal temperature -200℃ Temperature fluctuation: ≤±0.1℃ Temperature display resolution: 0.01℃ Torque range: 0-20N.M Torque display accuracy: 0.001 N.M Power supply: 50HZ, ~220V±10% Compressed air: ≥0.40Mpa Swing frequency: 100cpm (1.7HZ) Swing angle: ±0.5. ±1. Torque range: (0-5N.m, 0-10N.m 0-20N.m) automatic Ambient temperature: 0-35°C relative humidity <80% Setting range of vulcanization time: 2-300min, t90 is in the range of 10 seconds to 5 hours. Print content: date, time, temperature, curing curve, temperature curve, ML, MH, ts1, ts2, t10, t90, Vc1 Vc2 Dimensions: 600*700*1250mm 3. Main features: 1. This instrument adopts a truly closed cavity, and its repeatability and test data are comparable to Alpha 2. This instrument is based on a large-scale database development platform, and the temperature control device adopts software to directly control and collect and process. 3. This instrument has the functions of statistics, analysis, storage and comparison. Humanized design, easy to operate. Fourth, the main configuration: 1. The real high-precision closed cavity structure is synchronized with American Alpha. 2. Joint venture high-precision sensor with accuracy of 0.001N.M 3. Japan NSK high-precision bearings. 4. High-performance cylinders of SDPC Group, a Sino-British joint venture. 5. Sino-foreign joint venture Delixi pneumatic components. 6. Special modules with powerful functions, the test data is synchronized with Alpha. 7. The working door automatically rises and falls. 8. The key parts of electronic components adopt military components, with reliable quality and stable performance. 9. The computer software directly controls the temperature, and the accuracy of Alpha technology reaches 0.01℃. 10. 19-inch Lenovo LCD computer, HP color printer. 11. Taiwan built SUNON cooling fan to protect electrical appliances from malfunctioning and truly worry-free.
ZY-2000G Mooney Viscometer
ZY-2000G computer Mooney viscometer, measuring and temperature control circuit is composed of measuring and control module, platinum resistance, heater, can automatically track changes in the power grid and ambient temperature, automatically correct PID parameters, to achieve the purpose of rapid and accurate temperature control. The data acquisition system and electromechanical interlock complete the automatic test of the torque signal during the rubber test process, and automatically display the temperature value and set value in real time. After vulcanization, automatic processing, automatic calculation, printing Mooney, scorch curve and process parameters. The computer displays the test process in real time, and the changes of "temperature" and "time-Mooney" can be seen clearly from above. It is an indispensable instrument in the reclaimed rubber, rubber, wire and cable industries.
ZY-5000N rubber electronic tensile machine (digital display type)
ZY-5000N rubber electronic tensile machine is an instrument used to test the mechanical properties of materials such as stretching, peeling, tearing, and H extraction. It is widely used in rubber, plastic, textile, chemical, steel wire, hose tape, wire and cable, plastic, pipe and other industries. It is a high-precision, economical and practical instrument. The tensile machine is composed of a host, a speed control system, data acquisition and processing, sensors and electrical interlocking parts. The host includes the fuselage, transmission mechanism, and measurement system. Data processing is handled by a microcomputer processor. This machine uses a stepping speed regulator to change the stretching speed, and the speed value is directly read out. The motor moves the lower gripper (fixture) through the V-belt-worm-screw drive, so as to realize the tensile change of the sample. The head of the main unit is equipped with a tension sensor, and its upper end is connected with the connecting plate of the top beam of the main unit, and the lower end is connected with the upper clamp. The sensor is only subject to vertical tension and is not affected by torsion or directional force to ensure force measurement accuracy. Between the upper and lower grippers, the force of the sample during the test is transformed into an electrical signal through the force sensor and input into the microcomputer acquisition control system. After the test is over, it is automatically processed, automatically calculated, and the result is displayed. The touch LCD measurement and control system adopts 32-bit ARM technology and DSP high-performance processor control technology. The display part adopts a 7-inch 65K color ultra-clear touch screen with a resolution of 1024*768. The ultra-high performance configuration makes the software function and user experience great improve. The software includes boot animation, main screen display, large curve display, unit setting, multiple test standard selection and result calculation display, equipment status display, hardware parameter setting, equipment calibration, PID parameter setting, custom parameter editing, sample plan Editing, sample size editing, visual printing and other functions, the micro printer supports a variety of models to choose from, and the motor control supports free switching of multiple control methods such as servo, stepping, frequency conversion, and DC (the factory does not need to replace the system, and the standard features). This test measurement and control system is a high-performance measurement and control instrument designed specifically for electronic testing machines that integrates measurement and control. It can perform tensile, compression, bending, shear, tear, and peel tests. The software can complete the maximum force, maximum deformation, tensile strength, elongation at break, total elongation at maximum force, elongation at yield point, elongation after fracture, upper and lower yield strength, elastic modulus, force at yield point, and elongation at break , Calculation and real-time display of parameters such as elongation at yield point, tensile strength at break, tensile stress at yield point, constant elongation stress, constant elongation (according to user-specified constant force level) and other parameters, among which the level of constant elongation The value and the constant force level value can be entered into the relevant position of the software in the sample parameter interface according to the actual requirements of the customer. The parameters that can be calculated also include compressive strength, upper and lower compression yield strength, compression elastic modulus, bending strength, bending elastic modulus, average bending force, average peel force, peel strength, maximum peel force, minimum peel force, tear strength , Average shear force, shear strength, shear modulus and other mechanical and physical properties related parameters. Main interface function introduction
ZY-5000N Rubber Electronic Tension Machine
ZY series electronic tensile machine can be used for rubber, plastic, foam material, plastic, film, textile, fiber, polymer material, composite material, synthetic material, packaging tape, paper, wire and cable, fiber optic cable safety belt, leather belt, shoe Types, tapes, polymers, spring steel, stainless steel, castings, non-ferrous metals, auto parts alloy materials and other non-metallic materials and metal materials for stretching, compression, bending, tearing, 90° peeling, 180° peeling, shearing Cut, adhesion, pull-out force, elongation and other tests. Host specifications
ZY-500N Mask Tensile Machine
The ZY-500N mask tensile machine is an instrument used to test the mechanical properties of materials such as stretching, peeling, tearing, and H extraction. It is widely used in rubber, plastic, textile, chemical, steel wire, hose tape, wire and cable, plastic, pipe and other industries. It is a high-precision, economical and practical instrument.
ZY-500N Mask Tensile Machine
The ZY series mask tensile machine is used to measure the tensile properties of various masks. The appearance of this machine is novel and generous. Computer digital speed control system, equipped with force sensor and automatic elongation tracking device, good stability. Electrical appliances use PC and interface circuit boards to collect, store, process and print test results. The maximum force, yield force, average peel force, maximum deformation and other basic physical properties of the material can be calculated. During the test, the microcomputer collects the force value and deformation signal in real time, and the software displays the "force value-displacement" curve. After the test, it automatically calculates and saves the parameters, and can print out the report form the user needs. 2. Structural principle The host is composed of an electronic speed regulation system, a transmission mechanism, a force measurement system and an extension automatic tracking device. Electronic speed control system: The machine adopts AC speed control, corresponding to the stretching speed of 1-Xmm/min (X is the user's bottom request), and returns at high speed. Elongation tracking device: This device is used to measure the deformation of the sample. It can be tracked by an external tracker or a built-in tracker. It can also be tracked by the deformation device built in the motor without the tracker. 3. Main technical parameters 1. Force resolution: 0.001-0.1N 2. System accuracy: less than ±0.1 3. Maximum test force: 500N 4. Accuracy level: 0.5 5. Test force measurement range: 1-99% 6. Test force indication error: less than or equal to 0.3% 7. Test force resolution: 0.001 8. Displacement resolution: 0.001 9. Displacement indication error: less than or equal to 0.5% 10. Speed range: 0-500mm/min (special requirements can be customized) 11. Large stroke of gripper: 800mm 12. Elongation tracking error: ±0.1mm 13. Power supply voltage: AC220V±10% 50Hz 14. Net weight: 120KG Four, characteristics Automatic clearing: After the computer controls the test command, the system automatically clears; High intelligence: After the test, the fracture is automatically judged and the fixture automatically returns to the initial position Multi-function: different fixtures can be replaced to carry out different tests; Automatic shift: switch to different grades according to the size of the load; Change speed: the test speed can be changed arbitrarily Control method: Test methods such as test force, test speed, displacement and strain can be selected. Powerful: Record test data throughout the process. Provides functional services such as saving, comparison and tracking. The mouse can be used to arbitrarily find out the point-by-point force value and deformation data analysis of the test curve, and it can be partially enlarged and compared. Multiple protection: with automatic limit and automatic overload protection. Automatic calculation: automatically calculate various test results, and can modify the report arbitrarily Automatic length measurement: equipped with a high-precision encoder, automatically measuring the displacement stroke and elongation between punctuation. High taste: finely crafted, smooth lines, coupled with high-precision software and hardware technology and integration capabilities, reflecting the exquisite manufacturing technology and dexterity. Five, configuration 1. Single column type. 2. One high-precision sensor 3. Japan Omron high-precision photoelectric automatic tracker 4. The testing machine software has functions of automatic calculation, storage, comparison, etc. 5. High precision control drive system 6. High precision closed loop motor 7. German Thomson ball screw 8. Synchronous belt wheel transmission, no noise, no vibration, stable operation 9. 1 special test fixture 10. 19-inch Lenovo LCD computer, HP color printer.
ZY-5000N plastic electronic tensile machine (double column digital display)
ZY-5000N plastic electronic tensile machine is an instrument used to test the mechanical properties of materials such as stretching, peeling, tearing, and H extraction. It is widely used in rubber, plastic, textile, chemical, steel wire, hose tape, wire and cable, plastic, pipe and other industries. It is a high-precision, economical and practical instrument.
Development trend of vulcanizer 2020年09月19日
Tensile testing machine Tensing testing machine is also known as universal material testing machine. 2020年09月19日
Basic knowledge of universal testing machine 2020年09月19日
Test range of rubber mechanical properties 2020年09月19日
Three functions of rubber vulcanizer 2020年09月19日
Yangzhou Zhengyi Testing Machinery Co., Ltd.
Address: Zhenxing North Road, Zhenwu Town, Jiangdu District, Yangzhou City, Jiangsu Province